Faithfull Tools

The Faithfull Brad Point Wood Drill Bits are the preferred cutting tip design for drilling wood, chipboard and MDF. This alloy steel drill has a steeper twist and a deeper flute than HSS bits for rapid clearance of waste. Ideal for use in dowelling jigs.

5 Piece Lip & Spur Wood Drill Bit Set, these are the preferred cutting tip design for drilling wood, these alloy steel drills have a steeper twist and a deeper flute than HSS bits, for rapid clearance of waste. They are ideal for use in dowelling jigs.

Sizes: 4, 5, 6, 8 and 10mm.

4mm: Working Length: 43mm, Overall Length: 75mm.
5mm: Working Length: 50mm, Overall Length: 85mm.
6mm: Working Length: 52mm, Overall Length: 92mm.
8mm: Working Length: 75mm, Overall Length: 120mm.
10mm: Working Length: 80mm, Overall Length: 130mm.

The Faithfull Pencil Marking Set is designed to aid in the marking of hard to reach places such as drilled holes, tight corners and piping. Each pencil can be used to easily mark any surface, whether it’s wet or dry. If needed, the markings can be wiped clean with a damp cloth.

This set contains the following:

1 x Long Reach Marker.
1 x Pen Holder.
12 x Colour Refills in a handy carry case (6 Black, 3 Red, 3 Yellow).

Metal Cutting Discs are manufactured using Aluminium Oxide abrasive grit with fibreglass reinforcing and are resin bonded to provide both safety and optimum cutting performance. Discs with a 1.2mm thickness permit fine cutting where necessary on stainless steel and high grade metals.

They must never be used for grinding and must always be presented to the workpiece at an angle of 90º. For use with a variety of machines, mini-grinders to stationary cutting-off machines. It is important to choose between a metal or stone cutting disc according to the material being cut, and to ensure that the correct wheel is properly mounted.

Manufactured to EN 12413 standard.

SAFETY TIPS

Read the manufacturer's instructions carefully
Wear goggles to guard against flying chips or dust
Inspect the condition of the wheel frequently
Adjust the guard to deflect sparks and dust
Maintain the revs and let the wheel do the work

Metal Cutting Discs are manufactured using Aluminium Oxide abrasive grit with fibreglass reinforcing and are resin bonded to provide both safety and optimum cutting performance. Discs with a 1.2mm thickness permit fine cutting where necessary on stainless steel and high grade metals.

They must never be used for grinding and must always be presented to the workpiece at an angle of 90º. For use with a variety of machines, mini-grinders to stationary cutting-off machines. It is important to choose between a metal or stone cutting disc according to the material being cut, and to ensure that the correct wheel is properly mounted.

Manufactured to EN 12413 standard.

SAFETY TIPS

Read the manufacturer's instructions carefully
Wear goggles to guard against flying chips or dust
Inspect the condition of the wheel frequently
Adjust the guard to deflect sparks and dust
Maintain the revs and let the wheel do the work

Metal Cutting Discs are manufactured using Aluminium Oxide abrasive grit with fibreglass reinforcing and are resin bonded to provide both safety and optimum cutting performance. Discs with a 1.2mm thickness permit fine cutting where necessary on stainless steel and high grade metals.

They must never be used for grinding and must always be presented to the workpiece at an angle of 90º. For use with a variety of machines, mini-grinders to stationary cutting-off machines. It is important to choose between a metal or stone cutting disc according to the material being cut, and to ensure that the correct wheel is properly mounted.

Manufactured to EN 12413 standard.

SAFETY TIPS

Read the manufacturer's instructions carefully
Wear goggles to guard against flying chips or dust
Inspect the condition of the wheel frequently
Adjust the guard to deflect sparks and dust
Maintain the revs and let the wheel do the work

Metal Cutting Discs are manufactured using Aluminium Oxide abrasive grit with fibreglass reinforcing and are resin bonded to provide both safety and optimum cutting performance. Discs with a 1.2mm thickness permit fine cutting where necessary on stainless steel and high grade metals.

They must never be used for grinding and must always be presented to the workpiece at an angle of 90º. For use with a variety of machines, mini-grinders to stationary cutting-off machines. It is important to choose between a metal or stone cutting disc according to the material being cut, and to ensure that the correct wheel is properly mounted.

Manufactured to EN 12413 standard.

SAFETY TIPS

Read the manufacturer's instructions carefully
Wear goggles to guard against flying chips or dust
Inspect the condition of the wheel frequently
Adjust the guard to deflect sparks and dust
Maintain the revs and let the wheel do the work